Click To Call(689) 488-5644Click To Get A Free Estimate
Sealed brick paver driveway at a home in Pine Hills

Paver sealing for Pine Hills homes

Paver Sealing in Pine Hills, FL

From Robinswood to Silver Star Road, Pine Hills driveways get a free sealing estimate when you call (689) 488-5644.

  • Brings out deeper paver color
  • Fresh joint sand helps lock pavers in place
  • Gives weeds less room to grow
  • Makes the surface easier to keep clean
  • Free estimate, no obligation

Request a Free Estimate

Free, no obligation.

Step 1 of 2

Where are your pavers?

Please choose one.

Free EstimateNo obligation
Fast ReplyWithin 1 business day, usually much sooner
Typical Local Price$1.50 to $3.00 a sq ft to clean, sand and seal
Call Now(689) 488-5644
Paver sealing

Fast, careful paver sealing in Pine Hills

Paver sealing is available across Pine Hills, from the Robinswood streets off Pine Hills Road to the blocks along Silver Star Road. A local contractor can clean, re-sand and seal your driveway, walkways and patio, and the estimate is free. Call (689) 488-5644, and the answer arrives within 1 business day, usually much sooner.

Think about the drive you use every day. Tire marks cross the apron, the color has faded from red to a dull brick, and joints along the edge have opened. A wash, fresh sand and a new coat make it look cared for again. A written note works as well, so book your free estimate and describe the surface.

Pine Hills is a big unincorporated community on the west side of Orange County, with 22,219 homes. Some sit inside the City of Orlando after annexation, and some do not. The contractor goes by your street, not your mailing city. Call (689) 488-5644 and give the nearest cross road.

Call (689) 488-5644

Family relaxing by a sealed paver pool deck near Pine Hills
Why hire local

Why hire a local paver sealing contractor in Pine Hills?

Pine Hills homes range from 1950s ranches to newer builds, and the pavers around them are as mixed as the houses. A local contractor asks about that mix first, and a quick note through book your free estimate gets it started.

See the job before the price

A contractor looks at your Pine Hills pavers in person first. The number comes after, and you owe nothing for the look.

A yardstick for bids

Posted Central Florida rates span $1.50 to $3.00 per square foot, wash, sand and sealer included. Use that to judge quotes.

Matte or glossy, your call

Matte hides tire scuffs on a busy drive. Glossy brings out the red and charcoal but wears sooner. You choose after seeing both.

Dates that fit your week

Work, school and church all fill the calendar. Pick a window that suits you, and expect the contractor to shift it if storms roll in.

Get Your Free Estimate in Pine Hills

Tell us about your pavers in Pine Hills.

Call (689) 488-5644

Free, no obligation

Paver joint sand detail on a walkway near Pine Hills
Common problems

What paver problems show up most in Pine Hills?

Pavers of mixed ages with unknown coats

Pine Hills has been building since 1953, so driveways and patios were laid across seven decades. Some were sealed once, some twice, and some never. A water-based sealer cannot go over a solvent-based one, so the contractor has to find out what is on yours. An Orlando company says sealing over an old failing coat fails within months, so a test comes first. If you bought the home used, ask the seller or a neighbor what was done, and keep the answer for the next coat. Hyland Oaks, Signal Hill and the Silver Star Road blocks were all built in different decades, so no two streets share one history. Evans High School and the Central Florida Fairgrounds sit nearby, which shows how long this part of town has been built out.

Summer storms that strip the joint sand

When the wet season opens near the end of May, most of the year's rain follows. Roughly 61 percent of it falls in about five months, and storms tend to arrive in the late afternoon. Joints packed loosely lose sand quickly, and pavers start to shift. A coat that locks the sand in place makes a drive steadier through those months. Spring is the quiet window to repack the joints, before the wet season starts. Fall is the usual window, since the air dries out after October cold fronts.

Rust streaks from sprinklers

Sprinkler spray carries iron in many Florida yards, since most well water here is iron-rich, per University of Florida extension. The result is orange streaks along the drive edge. Those need their own treatment before sealing. A coat laid over rust locks it in, so tell the contractor where the heads aim. A small turn of each spray head costs nothing and cuts the streaks. Sprinklers installed decades ago may spray at odd angles now, so check where the water lands.

Daily wear on busy driveways

According to a Central Florida paver company, vehicles, oil and sun put the heaviest strain on a driveway. With 39.6 percent of Pine Hills households raising children, many drives work from morning to night. An Orlando company says busy driveways need resealing about every two to three years. Oil spots are treated during the wash so the coat bonds well. A sealed surface also cleans up more easily after the next oil drip, which means less scrubbing over time. Oil from a leaking engine soaks into bare pavers, which is another reason a coat helps. Cars parked in the same spot for years leave the clearest oil rings, and those get extra treatment.

Sun and humidity that wear down the coat

Florida sun runs hard on sealer about ten months a year. Humidity of 80 percent or more can turn a solvent-based coat white and make it peel. Faded color and a chalky feel are the early signs. When water stops beading on the surface, the coat has done its job and a fresh one is due. Ask the contractor to run the water test on your pavers so you can see for yourself how the coat is holding up. A faded, chalky surface is an early warning, so do the water test before the summer storms start. Humid air also slows drying, so a surface that looks dry at noon may still hold moisture in the joints.

Neighborhoods

Do Pine Hills' original subdivisions need a different sealing plan?

Often, yes. Robinswood and Pine Ridge Estates were the first subdivisions here, laid out in 1953 along the new Pine Hills Road. Homes that old have usually seen several owners and several rounds of work. A contractor will ask what is known about the pavers when you book your free estimate.

Later growth ran north toward Silver Star Road and Powers Drive and east along Indian Hill Road. Hyland Oaks, off North Hiawassee Road, is another distinct area. Each pocket has its own age and style. Call (689) 488-5644 and give the street, and the contractor can plan the visit accordingly.

Annexation in the 1980s moved parts of Pine Hills into the City of Orlando, including areas of Signal Hill and streets such as Clarion Drive. That means a Pine Hills address can carry an Orlando city line. The contractor works from your street, so give it when you book your free estimate. The estimate stays free either way.

Pricing

What does paver sealing cost in Pine Hills?

Think of price as area times rate. Companies serving the Central Florida market post rates from $1.50 up to $3.00 per square foot for washing, sanding and sealing. Oil spots, rust and an old failed coat sit toward the top of that span, while a clean, lightly worn surface sits near the bottom. Send your measurements with book your free estimate to turn that span into one number.

Most Pine Hills homes carry a drive, a front walk and a back patio. The contractor adds them together, so ask for the combined square footage and one line per extra. Stripping a failed coat costs more time than a simple wash. Dial (689) 488-5644 and ask which extras are likely on your lot.

Paved areaTypical exampleClean, sand and seal
300 sq ftSmall patio or walkway$450 to $900
600 sq ftTwo car driveway$900 to $1,800
1,000 sq ftLarge driveway or pool deck$1,500 to $3,000
1,500 sq ftDriveway plus pool deck$2,250 to $4,500

Math based on the $1.50 to $3.00 per square foot that Central Florida paver companies published as of November 2026. Your contractor sets the actual price after seeing the surface. Repairs, leveling and stripping failed sealer are usually extra.

Get a Free Estimate

Contractors sealing a paver driveway at a home in Pine Hills
How it works

How does a paver sealing job work in Pine Hills?

Ask what the surface already has

The contractor begins with a test on a hidden corner to learn whether the pavers were ever sealed. The answer sets the product, since a water-based coat cannot go over a solvent-based one. Sunken or rocking pavers are flagged for repair first. Tell the contractor how long you have owned the house and whether any paperwork came with it. A short list of past repairs and a few phone photos speed this step. If the pavers came with the house in the 1960s or 1970s, say so, since that tells the contractor how many coats may be under there.

Lift the oil, rust and green film

Hot water and a surface cleaner lift dirt and oil, and a separate treatment handles rust and algae. Runoff is kept away from plants and drains you care about. The pavers then sit until fully dry, which can take most of a day. Sealer will not bond to a damp surface, so this wait is never skipped. If a spot of oil has soaked deep, the contractor may repeat the treatment before moving on. Runoff from the wash is kept off the neighbor's lawn and out of the gutter where possible.

Pack every joint

Fresh sand goes into each gap and is set with water. Full joints stop pavers from rocking and leave weeds little room. If your drive has had open joints for years, this step takes longer than usual. The surface is brushed level afterward. Pavers that dipped over the years are lifted and reset first, so the joints sit level. Sand is set in two passes, and the surface is checked for low joints after the first soaking.

Choose the look on a test square

Matte keeps the natural color and hides tire marks well. Glossy deepens the red and charcoal but shows scuffs sooner. On a drive that works from morning to night, many owners lean matte. Check the square in daylight, not under a garage light. Hold the sample against the house trim before deciding. Compare the finished look to the garage door and trim, not just the pavers.

Two thin coats, then stay off

Sealer is sprayed in thin passes and rolled into the joints, because thin coats bond better than one heavy pass. The contractor watches the sky, since rain can turn the coat white. Keep feet off for a day or two and cars off for longer. Ask for firm times for your driveway. Keep the sprinkler timer off until the coat has cured, and park on the street in the meantime. Keep the car on the street until the contractor confirms the drive can take weight.

Services

Complete paver services in Pine Hills

Picture the work as four moves. Oil and rust come out in the wash, new sand fills the joints, the surface dries, and sealer is the final layer. Nothing dirty is sealed in. Ask by phone, at (689) 488-5644, how long each move takes on a driveway your size.

A busy drive wants a coat that forgives tires. A front walk wants one that handles leaves and feet. A back patio wants one that handles sun and sprinkler spray. Tell the contractor which one matters most by choosing book your free estimate, and the product choice will follow.

Check what is already on the pavers before choosing anything new. A water-based product will not bond over a solvent film, so the old coat sets the rules. Matte hides marks, while glossy shows them sooner. Call (689) 488-5644 and ask for both on a test square.

Pick a morning. Wet-season storms build late in the day, and sealer needs a dry start. Many Pine Hills jobs land in fall and winter, when the air is drier. Ask about open days after you book your free estimate, and have your cross streets ready.

Questions to ask before you hire

  • Do you price by the square foot or by the job, and is the estimate free?
  • How often should I plan to reseal in Central Florida sun and rain?
  • What happens if the sealer peels or turns cloudy after a few months?
  • How do you keep overspray off my plants, my lanai screens and my windows?
  • Can you send proof of insurance before anyone shows up at my house?
  • What do you do about the weeds and moss growing up through my joints?
  • Will the sealer leave a wet look, a satin look or a matte look?
Photos

What do sealed pavers look like around Pine Hills?

Homeowners standing on a sealed paver motor court at an arched stucco entry near Pine Hills
Sealed travertine pool deck inside a screened lanai near Pine Hills
Sealed terracotta and cream paver courtyard with a wall fountain and iron chairs near Pine Hills
Sealed herringbone brick paver walkway winding through azaleas to an arched door near Pine Hills
Close view of older brick pavers after sealing near Pine Hills
Shaded paver patio with one cleaned half beside a mossy half near Pine Hills
Contractor using a surface cleaner on a brick paver driveway near Pine Hills
Two contractors sealing a paver driveway at a ranch home near Pine Hills
Contractor talking through a paver sealing estimate with a homeowner in Pine Hills
Local

Why local matters in Pine Hills

Housing in Pine Hills runs from 1950s ranches in Robinswood to newer builds near Silver Star Road. A local contractor has seen both and plans the test, the wash and the finish for each. Someone from outside the area might treat them alike. Call (689) 488-5644 to reach a local contractor.

Rain shapes every schedule here. A crew that works the west side of Orlando keeps a spare day open and starts early, because late storms are routine in summer. Delays happen. A short message with book your free estimate is enough to ask how yours would be handled.

Driveways here have usually carried years of wear. A local contractor tests the surface first, so the new coat does not cloud over an old one. Dig out any receipt from a past job. When it turns up, book your free estimate and mention the product name.

Local roots

What is worth knowing about Pine Hills' growth as a suburb?

Pine Hills began in the early 1950s as a bedroom community for Martin Marietta workers. Gordon Barnett developed it as one of Orlando's first suburbs, with a country club, a golf course and a Hilton hotel. Pine Hills Road opened the way for the first subdivisions. If you live near Colonial Drive, book your free estimate and say so.

Silver Pines Country Club closed, and apartments went up on its land in the mid-1990s. West Colonial Drive was redone by 2011, and Evans High School was rebuilt on Silver Star Road. A near-replica of Graceland, built in 1981, stands in Hyland Oaks off North Hiawassee Road. For a home near any of these places, call (689) 488-5644 and name the street.

Questions

Frequently Asked Questions

How long does paver sealing last on a Pine Hills driveway?

One Orlando paver company says a natural finish lasts 3 to 5 years, while gloss and high-traffic drives last 2 to 3. A Pine Hills driveway with daily comings and goings leans toward the shorter span. Try a water test each spring: beading means the coat is working.

What is the average price for paver sealing in Pine Hills?

Expect a posted range of $1.50 to $3.00 per square foot across the Central Florida market. Oil, rust and an old failed coat push a Pine Hills quote toward the top. Ask that the quote state the total area.

What happens if pavers are not sealed in a place like Pine Hills?

Colors dull, stains take hold and joint sand washes out quicker. Weeds move into opened joints, and algae holds on where shade keeps things damp. Sun and humidity speed all of it up. A coat slows that wear, though it never stops it completely.

Why is paver sealing so expensive for a big Pine Hills drive?

Labor and prep drive most of the price. Cleaning, waiting for it to dry, repacking the joints and spraying thin coats fill a day or more. Stripping a failed coat adds hours. A large drive also adds area, which is what the rate multiplies.

Is it better to spray or roll paver sealer on Pine Hills pavers?

An Orlando paver company describes spraying at low pressure and then back-rolling. Spraying lays the coat down, and rolling presses it into the joints. Thin passes bond better than one heavy pass.

Can I seal over old sealer on my Pine Hills pavers?

Not always. A water-based product will not bond over a solvent-based one, and a white or peeling coat must be stripped first. A quick test on your pavers shows what is already there. Sealing over a failed coat fails within months.

Does a City of Orlando address inside Pine Hills change anything?

No. The contractor works from your street, whether the mailing line says Pine Hills or Orlando. Parts of the community were annexed in the 1980s, so both are common. Send your street and nearest cross road.

Which finish suits a busy Pine Hills driveway?

Many owners pick matte, since it hides tire scuffs. A glossy finish pops color but shows marks sooner and needs redoing sooner. Ask the contractor for a test square so you can compare them in daylight.

How soon can cars use a sealed Pine Hills driveway?

Wait 24 to 48 hours before walking on it, and longer before parking, as an Orlando company points to about 72 hours for vehicles. Humidity and shade can add time. Get firm times from the contractor for your drive.

Should I seal my Pine Hills pavers before selling the house?

It can help. A clean, sealed driveway and patio look cared for in photos and in person. The cost follows square footage inside the posted range, and the work takes about a day. Ask for timing that fits your listing date.

Do many contractors cover Pine Hills?

Yes, since it is a big community near major roads. Because so many companies work this area, comparing two or three quotes is easy. Check the square footage, the stages listed and the keep-off times in each one.

What are the downsides of sealing pavers on a Pine Hills driveway?

The main downsides are upkeep and timing. A coat wears and needs redoing, a wet look shows scuffs sooner, and the surface must be fully dry before the job. Those points matter on a busy Pine Hills drive, so ask the contractor how they apply to yours.

Ready for a Free Estimate in Pine Hills?

Call (689) 488-5644 and tell us about your pavers.

Call (689) 488-5644

Free, no obligation