
A second chance for worn-out pavers
Paver Restoration and Resealing in Winter Park, FL
Call (689) 488-5644 for a free estimate to strip, re-sand and reseal tired Winter Park pavers.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Can tired pavers in Winter Park be restored instead of replaced?
A local contractor restores and reseals pavers throughout Winter Park, FL, and you will hear back within 1 business day, usually much sooner. The estimate costs nothing and you can say no. To begin, call (689) 488-5644.
Most pavers that look finished are not. The stone underneath is sound, and what failed is the coat, the sand or the level of a few pieces. Fixing those is far less work than ripping out a driveway. A contractor can tell you which problem you have after one close look, and then explain what each fix involves and what it costs. Describe the surface and how old the last coat is when you ask. To arrange that look, book your free estimate.
How do I tell the old sealer has failed?
Failed sealer announces itself. Peters Pressure Washing lists whitening, cloudiness and haze as the signs, and it blames trapped water vapor, coats laid on too thick, poor prep and incompatible products. In a humid city that spends a long summer under afternoon clouds, trapped moisture is the one to watch. To have a patch checked, call (689) 488-5644.
White or milky patches
Moisture got trapped under the film, and it shows most after a wet week.
Peeling edges
A coat laid too thick or over a dirty surface lets go in flakes, usually near steps and joints.
Blotchy gloss
Some areas shine and others look flat, often where the coat was applied in stages.
Color that went flat in months
Castle Clean and Seal says cheap sealers break down in 6 to 12 months under Florida sun.
Water soaks in
Drops that used to bead now darken the stone, which means the coat has thinned.
Stains trapped under the film
Castle says sealer over dirty pavers traps stains permanently.
Which Winter Park towns can get paver restoration?
A contractor who serves Winter Park also covers the towns below, and each town page has local notes. Not seeing your street? Ring (689) 488-5644 and ask.

Does failed sealer have to come off before resealing?
Yes. Peters Pressure Washing says resealing over failing layers makes the coat turn white again, and Castle Clean and Seal says failed sealer often has to be chemically stripped before new sealer can bond. A new coat is only as good as what it sticks to. To find out whether yours needs stripping, call (689) 488-5644.
Stripping is a slow job. Peters Pressure Washing says it takes a stripper to break the bond and then a surface cleaner with vacuum recovery, since without recovery nearly all of the old sealer cannot be removed. Paver Sealing Orlando puts stripping at two to three days against one for a standard job. Ask how the contractor captures the runoff when you book your free estimate.
When a wash and new coat are enough
If the old coat is only faded and still sound, stripping may not be needed. The contractor looks at the surface and tells you which case you have. A faded but intact coat is a cheaper fix than a cloudy one. To compare the two, call (689) 488-5644.
What is the paver restoration process, from first look to last coat?
Seven steps cover most jobs, and stripping or repairs only appear when the surface calls for them. The order never changes. To schedule a visit, call (689) 488-5644.
1. Inspect the surface
The contractor walks the area and notes failed sealer, low pavers, empty joints, stains and standing water.
2. Strip where needed
A stripper breaks the bond with the old coat, and a surface cleaner with vacuum recovery lifts it.
3. Reset low pavers
Sunken or loose pieces are lifted, the bedding is corrected and the pieces are relaid.
4. Clean and rinse
An algae treatment and a low pressure wash come next, and the surface drains.
5. Refill the joints
Coarse, angular silica sand goes in, and the contractor settles it so no gaps remain.
6. Let everything dry
Sealer needs a dry surface, and rushing this step is where cloudy coats begin.
7. Apply the new sealer
One even coat goes down at the label rate, and the contractor walks the area with you.
What if some of my pavers have sunk or tilted?
Low pavers can be lifted and relaid with the bedding corrected underneath. Sealer will not raise them, because a gap stays a gap under any coat. Mention every dip when you call (689) 488-5644.
Winter Park sits on Florida's limestone, and its history includes a sinkhole. Wikipedia describes a May 1981 sinkhole near Denning Drive and Fairbanks Avenue and calls West Winter Park sinkhole-prone. Most dips in a patio are settled bedding, not a hole in the ground. A dip that keeps growing, or a crack in a nearby wall, is worth a call to someone who looks at the ground. To have a contractor look at yours, book your free estimate.
How are paver joints refilled so the sand stays put?
Joint sand washes out and settles over time, according to Peters Pressure Washing, and a Winter Park summer rain speeds that up. The fix is to refill the joints with coarse, angular silica sand and settle it. Peters says wet sanding packs the sand tightly, while dry sanding can bridge and leave air pockets. To ask which method a contractor uses, call (689) 488-5644.
A flood coat that soaks the joints bonds the sand in place, which limits sand loss, weeds and ant mines, Peters adds. That helps a driveway that keeps emptying after storms. If your joints drop below the paver edges every season, book your free estimate.
Why weeds come back through old joints
Empty joints give seeds a place to land and a pocket of damp air. Packed joints leave far less room, which is why sand work is part of every restoration.
Why wash before sealing a restored paver?
A coat holds whatever sits under it. Castle Clean and Seal warns that sealer applied over dirty pavers traps stains permanently. Algae, oil and leaf marks should come out first, so the new finish covers clean stone. To plan the wash, call (689) 488-5644.
Restore, reseal or replace: which job fits my pavers?
Most pavers qualify for the first two. Replacement comes up when pieces are cracked through or the base below has failed. The contractor can say which path fits after the first look. To get that opinion, book your free estimate.
Reseal only
The old coat is sound and only faded. A wash, fresh sand and a new coat usually do it.
Strip and reseal
The coat is white, peeling or blotchy. It comes off before anything new goes on.
Reset and reseal
Some pavers have sunk or rock underfoot. They are relaid, then the surface is finished.
How long does restoration take?
Paver Sealing Orlando says a standard clean, sand and seal takes about a day, while stripping takes two to three. The sealer then needs time. Water-based sealer is walkable in 3 to 4 hours and cured in 24 to 48, and solvent-based can need up to 72 hours. Castle Clean and Seal asks for 4 to 6 hours before foot traffic, 24 hours for furniture and 48 hours before cars. To plan around those windows, call (689) 488-5644.
What does paver restoration cost in Winter Park?
Paver Sealing Orlando publishes $3.50 to $5.00 per square foot to strip and reseal, and it lists typical projects at $1,750 to $5,000. Castle Clean and Seal says stripping failed sealer usually adds $500 to $1,000 or more to a standard job and sets a $1,000 project minimum. Leveling and repairs cost extra. For a number written for your home, book your free estimate.
The standard clean, sand and seal is cheaper, at $1.50 to $3.00 per square foot around Central Florida. That price assumes the old coat can stay. If a quote for restoration lands far under these ranges, ask which steps it skips. Holding a quote already? Call (689) 488-5644.
If you only need a wash and a coat, read about paver sealing, or see how stain removal fits in, or return to Winter Park paver sealing.
| Paved area | Typical example | Strip and reseal at $3.50 to $5.00 |
|---|---|---|
| 400 sq ft | Back patio and walkway | $1,400 to $2,000 |
| 800 sq ft | Wide two car driveway | $2,800 to $4,000 |
| 1,200 sq ft | Driveway with entry and walk | $4,200 to $6,000 |
This table multiplies the $3.50 to $5.00 per square foot that Paver Sealing Orlando publishes for stripping and resealing, which it ties to typical projects of $1,750 to $5,000 and a job of two to three days. Castle Clean and Seal says stripping failed sealer usually adds $500 to $1,000 or more to a standard job. Sunken pavers and repairs cost extra and are quoted after a visit.

What should a restoration estimate list?
Ask for lines you can compare. The estimate should show stripping, repairs, joint sand and sealer on separate lines, with the area in square feet. That way two bids line up. To request one in writing, call (689) 488-5644.
Area and condition
Square footage and what was found: old sealer, low spots, stains and standing water.
Stripping line
Present only if the coat has failed, and priced on its own.
Repairs line
Pavers to be lifted and relaid, with the number of pieces or the area.
Sand and sealer
The product name, the sheen and how the joints will be filled.
What do restored pavers look like around Winter Park?








Why choose a local contractor for paver restoration?
Restoration depends on judging a surface, and a contractor who works around Winter Park knows how lake humidity and summer storms treat old sealer. The estimate is free, the price comes in writing and the decision is yours. To begin, book your free estimate.
Contractors who know the area
A company that works in and around Winter Park already deals with oak shade, lake humidity and summer storms. That makes the first visit more useful.
Free to ask
The visit and the estimate cost nothing. If the number does not suit you, you can say no and owe nothing.
Prices you can check
Central Florida companies publish what they charge per square foot, and this site shows that range. A bid far above or below it deserves a question.
You set the pace
Ask for the price on paper, then take as long as you like to decide. Before signing, read the contractor standards page for the points worth confirming.
What do Winter Park homeowners ask about paver restoration?
Cost, how long sealer lasts and why it goes white come up most. The answers follow, and for anything else, call (689) 488-5644.
Is it necessary to seal pavers in Florida?
It is not required. A sealed surface resists stains and slows fading, and the trade-off is a repeat job every few years. Paver Sealing Orlando says sealer typically lasts two to four years, so a restoration visit usually comes up when the last coat has already worn out or failed.
How can I make my pavers look new again?
Start by learning what is wrong. Faded color with sound sealer may need only a wash and a new coat, while white or cloudy sealer has to come off first. Peters Pressure Washing, a Tampa company, says resealing over failing layers turns white again.
What is the average cost to seal pavers in Florida?
A standard clean, sand and seal is posted at $1.50 to $3.00 per square foot by Orlando-area companies. Strip and reseal is higher, at $3.50 to $5.00 per square foot on the Paver Sealing Orlando page. A contractor sets the real price after seeing the surface.
How long does sealer last on pavers in Florida?
Paver Sealing Orlando says two to four years, with a maintenance cleaning every 12 to 15 months to extend it. Castle Clean and Seal warns that cheap sealers break down in 6 to 12 months under Florida's UV exposure. The product matters as much as the date.
Why did my sealer turn white?
Peters Pressure Washing lists trapped water vapor, a coat laid on too thick, poor prep and an incompatible product as the usual causes. Humid Winter Park summers raise the odds of trapped moisture. Cloudy sealer usually has to be stripped before a new coat will look right.
Does old sealer always have to be stripped?
No, but failed sealer does. Castle Clean and Seal says old sealer often needs chemical stripping before new sealer can bond. If the old coat is only faded and still sound, a wash and fresh coat may be enough. A contractor can tell after a close look.
How long does paver restoration take?
Paver Sealing Orlando says a standard clean, sand and seal takes about a day and stripping takes two to three. Water-based sealer is walkable in 3 to 4 hours and cured in 24 to 48, and solvent-based can need up to 72 hours.
Can sunken pavers be fixed during restoration?
Often yes. A contractor can lift the low pavers, add bedding material and relay them. Sealer will not raise a low spot, so leveling comes first. If a dip keeps growing or sits near a sinkhole-prone area, ask who should look at the ground.
Why do joints keep emptying on my driveway?
Joint sand washes out and settles over time, according to Peters Pressure Washing. Heavy summer rain speeds that up. Refilling the joints and bonding the sand with a flood coat slows the loss, and it gives weeds and ants less room.
Is wet sanding or dry sanding better for paver joints?
Peters Pressure Washing says wet sanding packs the sand tightly, while dry sanding can bridge and leave air pockets. It also names coarse, angular silica sand as the right kind. Ask the contractor which method and which sand they use.
Ready to restore your Winter Park pavers?
Share your street and what looks wrong, and a local contractor writes back within 1 business day, usually much sooner.
Free, no obligation
