Click To Call(689) 488-5644Click To Get A Free Estimate
Sealed brick paver driveway at a home in Union Park

Paver sealing for Union Park homes

Paver Sealing in Union Park, FL

Near Jay Blanchard Park in Union Park, a free paver sealing estimate starts when you call (689) 488-5644.

  • Brings out deeper paver color
  • Fresh joint sand helps lock pavers in place
  • Gives weeds less room to grow
  • Makes the surface easier to keep clean
  • Free estimate, no obligation

Request a Free Estimate

Free, no obligation.

Step 1 of 2

Where are your pavers?

Please choose one.

Free EstimateNo obligation
Fast ReplyWithin 1 business day, usually much sooner
Typical Local Price$1.50 to $3.00 a sq ft to clean, sand and seal
Call Now(689) 488-5644
Paver sealing

Fast, careful paver sealing in Union Park

Paver sealing is available in Union Park, from the streets by North Dean Road to the blocks near Rouse Road. A local contractor washes the surface, packs the joints and seals driveways, walkways and patios, and the estimate is free. Dial (689) 488-5644 and a reply will reach you within 1 business day, usually much sooner.

Picture the front walk your guests use. Leaves have left brown streaks, the joints are thin and gritty, and the color has gone flat. Once the surface is cleaned, re-sanded and sealed, the walk reads as one calm, even piece again. Writing is fine too: book your free estimate and describe the spot.

Union Park sits southwest of the University of Central Florida, and the Econlockhatchee River runs along its west and north edges. That setting is what makes a local contractor useful here. Ask about trees, drainage and sprinklers when you call (689) 488-5644.

Call (689) 488-5644

Family relaxing by a sealed paver pool deck near Union Park
Why hire local

Why hire a local paver sealing contractor in Union Park?

Union Park has a river on two sides and a busy park at its center. A local contractor plans around both, and you can book your free estimate to see how that works on your street.

No-charge first visit

The contractor studies your Union Park pavers before naming a number, and the estimate carries no obligation.

A figure to measure against

Orlando-area sealing pages list $1.50 to $3.00 per square foot, wash and coat included. Use that to check any bid.

A finish for the way you live

A wet look deepens color and shows scuffs sooner. Matte stays calmer near a pool or a busy entry.

You set the pace

Pick the day, pick the finish, or say no thanks. Nothing about a Union Park estimate locks you in.

Get Your Free Estimate in Union Park

Tell us about your pavers in Union Park.

Call (689) 488-5644

Free, no obligation

Paver joint sand detail on a walkway near Union Park
Common problems

What paver problems show up most in Union Park?

Leaf stains from the river corridor

The Econlockhatchee is a blackwater river with a forested floodplain, and it borders Union Park on the west and north. Wooded ground means leaves, and leaves leave tannin stains on pavers. An Orlando paver company treats tannin as its own stain type during washing. Sealer put over a stain would hold it in place, which means the cleaning has to come first. Ask for a test patch if a stain looks deep. The Little Econ Greenway Trail runs through Jay Blanchard Park nearby, a reminder that wooded, leafy ground is never far.

Joints that empty after summer storms

The wet season in Orlando begins near May 24, and about 61 percent of the yearly rain falls then, mostly in afternoon storms. Sand washes out of joints that were never filled well. Weeds then root in the widened gaps, and the pavers start to shift. Fresh sand packed in by a wet sand process, then sealed, holds up far better to those storms. A sealed joint also drains more evenly. Spring checks of the joints near the curb are easy to do from the driveway and cost nothing.

Orange streaks from irrigation

Most Florida well water is high in iron, according to University of Florida extension, and irrigation water with iron leaves orange streaks. Check the strip of driveway nearest your sprinkler heads. Rust gets treated during the wash. A sealer coat laid on top of it would make the stain harder to remove later, so tell the contractor if you see orange lines near the street. Mention which side of the house the sprinklers cover, and the contractor can focus on the right edge of the walk.

White haze on newly laid pavers

Fresh pavers can rise with a white mineral haze called efflorescence as they cure. An Orlando company advises waiting 30 to 90 days before the first seal. Sealing over the haze traps the salts and leaves a cloudy film that is hard to fix. If your pavers are new, say so at the estimate, and the contractor will tell you when they are ready. Pavers laid in the last few months often still carry that haze on the south side first, where the sun bakes them.

Cloudy or peeling old sealer

Some Union Park pavers may carry a coat from an earlier owner. In Central Florida humidity, a solvent-based coat can turn white and peel. A water-based product cannot be applied over it, so the old coat has to be identified or stripped first. Bring any receipt or product name you can find, since that can save an hour of testing. A faint white film on an older drive can be a failed coat rather than efflorescence, and a test patch tells the two apart.

Neighborhoods

Where in Union Park can I get paver sealing?

Anywhere inside the community's lines. Union Park runs from North Dean Road and the Econlockhatchee on the west to Rouse Road on the east. Bloomfield Drive marks the south edge, and J Blanchard Trail marks the north. Give the contractor your cross streets when you book your free estimate, and the estimate can start from there.

The 2020 census counted 3,853 housing units here, with a median age of 35.4. Nearly 30 percent of households had children under 18. Busy family driveways wear fast, since cars, scooters and chalk games all work on the same surface. Call (689) 488-5644 and mention how your driveway is used, so the finish can match the traffic.

Union Park sits at 82 feet above sea level, close to the river and its flood-control works. Michaels Dam in Jay Blanchard Park was built in 1965 for flood control. Low corners of a lot can hold water after a storm, which pushes back a sealing day. Ask the contractor to check those corners, then book your free estimate to hold a date.

Pricing

What does paver sealing cost in Union Park?

Around Orlando the posted range is $1.50 to $3.00 per square foot, covering the wash, the sand and the coat. A Union Park driveway with leaf stains or heavy algae needs more prep, which pushes the price up. A clean, recently sealed surface lands lower. To get a figure for your pavers, book your free estimate.

Size changes the total more than any other factor. A long driveway plus a back patio costs more than a short entry walk, even at the same rate. Efflorescence, rust and old failing sealer each add washing or stripping time. Call (689) 488-5644 and ask that every extra be listed before work starts.

Paved areaTypical exampleClean, sand and seal
300 sq ftSmall patio or walkway$450 to $900
600 sq ftTwo car driveway$900 to $1,800
1,000 sq ftLarge driveway or pool deck$1,500 to $3,000
1,500 sq ftDriveway plus pool deck$2,250 to $4,500

Math based on the $1.50 to $3.00 per square foot that Central Florida paver companies published as of November 2026. Your contractor sets the actual price after seeing the surface. Repairs, leveling and stripping failed sealer are usually extra.

Get a Free Estimate

Contractors sealing a paver driveway at a home in Union Park
How it works

How does a paver sealing job work in Union Park?

Walk the lot with the contractor

The visit starts outside. The contractor notes where leaves fall, where sprinklers hit, and where water sits after rain. Low or sunken pavers are marked, since sealer would keep a dip. If the pavers are new, the contractor asks when they were laid, because fresh pavers may need weeks of curing. Bring up any past standing water on your lot. Michaels Dam and the park's flood-control history are a good reminder to point out any low corner that holds water.

Treat and wash the surface

Algae and mildew get a pre-treatment. Washing then lifts dirt, tannin from leaves, rust and oil. Cleaner and rinse water stay off plants and out of pool water. Wet pavers are never sealed, so the surface is left to dry afterward. In shade, that can take a full day, so the contractor may split the job across two days. Spray from the wash is steered away from the street and the storm drain at the curb.

Pack the joints with polymeric sand

New joint sand goes in after the wash. An Orlando company says polymeric sand locks pavers and resists washout. The surface is swept and the sand is set with water. Skipping this step lets the first hard storm empty the joints again. If your joints have been open a long time, expect this stage to take longer than average. Sand is brushed in at an angle so the joint fills from side to side, not just along the top.

Choose penetrating or wet look

Penetrating sealer soaks in and keeps a natural matte look with good traction when wet. Film-forming sealer sits on top, deepens color and needs redoing sooner. Pool decks and travertine usually call for the penetrating type. A Union Park contractor can show you both finishes on a small patch, so you can pick before the full coat goes down. Ask for the test square to be on a corner you walk past every day.

Apply thin coats and keep traffic off

The coat is laid on thin and even, since two thin coats hold better than one thick one. Foot traffic usually waits 24 to 48 hours, and cars wait longer. Published guidance runs two to five years before the next coat. Check the forecast with the contractor before the day you set, and keep sprinklers off until the coat has cured. Close the garage side of the drive first so nobody tracks across wet sealer, then reopen it when the contractor says so.

Services

Complete paver services in Union Park

A Union Park sealing job has four stages: treat and wash, refill the joints, dry fully, then seal. Dirt never gets trapped because the coat comes last. Ask how long the drying stage takes under your trees. Call (689) 488-5644 to talk through the schedule.

Driveways need a finish that handles tires. Back patios need one that shrugs off leaves and sprinklers. Pool decks need good traction when wet, which is why penetrating sealer is the usual pick there. Name the surface you care about most with book your free estimate, and the plan will start there.

Sealer comes in water-based and solvent-based types, plus matte and wet-look finishes. Layering water over solvent fails, so the old product has to be known. Matte keeps a natural color, and wet look shows scuffs sooner. Call (689) 488-5644 to compare the two on your pavers.

Weather sets the date. Orlando's wet season starts in late May, and storms build in the afternoon, so early starts help. October brings drier air as the season ends, though shade under river-corridor trees can slow drying. To see which days are open near you, book your free estimate.

Questions to ask before you hire

  • How long does my patio have to stay clear after the sealer goes down?
  • Does an afternoon thunderstorm change your schedule on the day of the job?
  • What do you do about the weeds and moss growing up through my joints?
  • Do you strip the old sealer first, or can you seal over it?
  • Will the sealer leave a wet look, a satin look or a matte look?
  • What do you check on my pavers before you give me a price?
  • Do you price by the square foot or by the job, and is the estimate free?
Photos

What do sealed pavers look like around Union Park?

Homeowners standing on a sealed paver motor court at an arched stucco entry near Union Park
Sealed travertine pool deck inside a screened lanai near Union Park
Sealed terracotta and cream paver courtyard with a wall fountain and iron chairs near Union Park
Sealed herringbone brick paver walkway winding through azaleas to an arched door near Union Park
Close view of older brick pavers after sealing near Union Park
Shaded paver patio with one cleaned half beside a mossy half near Union Park
Contractor using a surface cleaner on a brick paver driveway near Union Park
Two contractors sealing a paver driveway at a ranch home near Union Park
Contractor talking through a paver sealing estimate with a homeowner in Union Park
Local

Why local matters in Union Park

A contractor who knows Union Park knows it sits beside a blackwater river with leafy banks. That means tannin stains and damp shade are routine on nearby yards. A crew from across town may not plan for them, and the stain can come back under a fresh coat. For a local contractor, dial (689) 488-5644.

Local knowledge also helps with timing. Afternoon storms build between 4 and 6 during the wet season, so a morning start is common. A contractor who works east Orlando knows to check the sky before opening the sealer. Send a note with book your free estimate to learn how a weather delay is handled and what happens to your date.

Union Park has many families, and driveways here work hard. A local contractor will ask how many cars use the drive and where kids play. That shapes the finish you choose, and how long you stay off the surface. If you want advice before booking, call (689) 488-5644 for a free estimate with no pressure.

Local roots

What landmarks help me describe where I live in Union Park?

Jay Blanchard Park is the easiest one. It sits at 3451 North Dean Road and holds courts, playgrounds, soccer fields, a pool and the Blanchard Park YMCA Family Center. The park is named for the first director of Orange County parks. If your street is near it, book your free estimate and say so, since that helps place your lot.

The Little Econ Greenway Trail runs through the park along the Little Econ River, an 18-mile tributary of the Econlockhatchee. Michaels Dam, built in 1965 for flood control, is now a fishing spot. The University of Central Florida lies just to the northeast. If one of these is close to you, call (689) 488-5644 with your cross street.

Questions

Frequently Asked Questions

How many years does paver sealing last in Union Park?

Published figures put a recoat anywhere from two to five years out. One Orlando company puts natural finishes at 3 to 5 years, with gloss and busy driveways nearer 2 to 3. Shade from river-corridor trees and daily car traffic push a Union Park drive toward the shorter end.

What does paver sealing cost on average for a Union Park driveway?

Posted rates in the Orlando area span $1.50 to $3.00 per square foot, all stages included. Leaf stains, algae, efflorescence and old failing sealer move a Union Park job within that range. The quote should state the full square footage being sealed.

Can pavers in Union Park be pressure washed without sealing?

Washing is part of every sealing job, since sealer needs a clean, dry surface to bond. A paver company in Orlando uses washing, with treatment for rust, oil and tannin, before drying and sealing. Washing alone empties joint sand, so fresh sand goes in afterward.

What happens to Union Park pavers if they are not sealed?

They fade and stain faster, and the joint sand washes out in storms. Weeds and algae then move in where shade keeps the surface damp. Orlando humidity and sun speed all of that up. Sealing slows it, though it does not stop it.

Should you seal pavers after power washing in Union Park?

Yes, once the surface is completely dry and the joints hold fresh sand. A cleaned paver that stays bare takes on stains quickly. Sealing over damp pavers can turn the coat white, so the contractor waits. Shaded Union Park yards may need a full day to dry.

How much does a Union Park driveway cost to seal?

A driveway falls inside that same posted range. Multiply by the square footage to get a rough total. Add washing for leaf stains and rust if your drive needs it. A free estimate gives the real figure.

Can I seal new pavers in Union Park right away?

Wait first. An Orlando paver company says to leave new pavers 30 to 90 days so curing finishes and efflorescence clears. Sealing too early traps the salts and leaves a cloudy white haze. The contractor can check your pavers and tell you when they are ready.

How long until I can use my Union Park driveway after sealing?

Plan on a day or two before walking on it, and about three days before parking. One Orlando company puts vehicles at roughly 72 hours. Humidity and shade can stretch that, so ask for firm times.

Does Union Park's river setting affect paver sealing?

It can. The Econlockhatchee is a blackwater river with a forested floodplain, so leaves, tannin stains and damp shade are common nearby. Those get washed before sealing. Tell the contractor if trees hang over your pavers. Ask for a quote that lists any extra washing time so the total is clear up front.

What does a clean and seal job include in Union Park?

A full job treats algae, washes with targeted stain removal, dries the surface, refills the joints with polymeric sand and applies thin coats of sealer. An Orlando company describes the same order. Ask the contractor to list each stage in writing. That way you can compare two quotes line by line instead of by the bottom number alone.

Will sealing change the color of my Union Park pavers?

A matte or penetrating sealer keeps the natural color, while a film-forming wet look deepens it. The wash alone will brighten pavers that have gone dull. Ask the contractor to test a small corner so you can see the result before the full job. Wet look pops the red and charcoal, though it shows tire scuffs sooner on a driveway.

What should I have ready before a Union Park paver estimate?

Know roughly how big the area is and whether the pavers were ever sealed. Note any stains, sunken spots or weeds. Mention your sprinkler schedule and any shade from trees. That lets the contractor quote closer to the final number. A few photos from your phone also help the contractor judge the job before the visit, and they speed up the quote.

Ready for a Free Estimate in Union Park?

Call (689) 488-5644 and tell us about your pavers.

Call (689) 488-5644

Free, no obligation